Module 12 / Water Vapour and the Water Cycle
Project Atmosphere Canada
Project Atmosphere Canada (PAC) is a collaborative initiative of
Environment Canada and the Canadian Meteorological and
Oceanographic Society (CMOS) directed towards teachers in the
primary and secondary schools across Canada. It is designed to
promote an interest in meteorology amongst young people, and
to encourage and foster the teaching of the atmospheric
sciences and related topics in Canada in grades K-12.
Material in the Project Atmosphere Canada Teacher's Guide has
been duplicated or adapted with the permission of the American
Meteorological Society (AMS) from its Project ATMOSPHERE
teacher guides.
Acknowledgements
The Meteorological Service of Canada and the Canadian
Meteorological and Oceanographic Society gratefully
acknowledge the support and assistance of the American
Meteorological Society in the preparation of this material.
Projects like PAC don't just happen. The task of transferring the
hard copy AMS material into electronic format, editing, re-writing,
reviewing, translating, creating new graphics and finally format-
ting the final documents required days, weeks, and for some
months of dedicated effort. I would like to acknowledge the
significant contributions made by Environment Canada staff and
CMOS members across the country and those from across the
global science community who granted permission for their
material to be included in the PAC Teacher's Guide.
Eldon J. Oja
Project Leader Project Atmosphere Canada
On behalf of
Environment Canada and the Canadian Meteorological and
Oceanographic Society
All rights reserved. No part of this publication may be
reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, photocopying, recording or otherwise without
the prior written permission of the publisher.
Permission is hereby granted for the reproduction, without alteration, of materials
contained in this publication for non-commercial use in schools or in other
teacher enhancement activities on the condition their source is acknowledged.
This permission does not extend to delivery by electronic means.
Published by Environment Canada
© Her Majesty the Queen in Right of Canada, 2001
Cat. no. En56-172/2001E-IN
ISBN 0-662-31474-3
Contents
Introduction
The substance known as water exhibits a unique set of chemical and physical
characteristics. These unusual properties include its ability to exist as solid,
liquid or vapour at the temperatures and pressures found at and near the Earth's
surface. This enables water to circulate through the atmosphere, ocean and solid
earth, forming endless cycles which are known collectively as the hydrologic
or water cycle. Water vapour plays a key role in the water cycle while acting
as a small but critical atmospheric constituent. This module investigates the
role of water vapour in the atmosphere; where it comes from, where it goes,
how it is measured, and how its presence can be detected.
Basic understandings
The Substance Water
- Water is a unique substance that is essential to life and a key ingredient
of our weather and climate system.
- Water is the only naturally occurring substance found in significant quantities
in solid (ice), liquid (water) and gaseous (vapour) phases at the temperatures
and pressures found at and near the Earth's surface.
- Water substance changes phase with relative ease at and near the Earth's
surface, and is continually flowing to, through, and from the atmosphere.
- The atmosphere, with water vapour playing a major role, maintains the hydrologic
(water) cycle by redistributing water from land and ocean reservoirs to every
place on Earth, the highest elevations included.
- Large quantities of heat energy, called latent heat, are absorbed (released)
when water changes phase from vapour to liquid to solid (solid to liquid to
vapour). The energy absorbed or released during these phase changes in the atmosphere
have a major impact on weather and climate.
The Water (Hydrologic) Cycle
- The overall picture of the exchange of water in all its phases among the
atmosphere, ocean and solid earth is called the water cycle.
- The global atmosphere contains just 0.001% of the water found near the Earth's
surface, while the other major reservoirs are the oceans (97%), ice caps and
glaciers (2%), ground water (0.6%), and rivers and lakes (0.01%).
- Compared to the other global water reservoirs, the residence time of water
substance in the atmosphere is very short. Every ten days, the amount that passes
through the atmosphere is equal to its total water content at any one time.
- Water enters the atmosphere by evaporation. Atmospheric motions transport
the vapour elsewhere and, eventually, it condenses and may return to the Earth's
surface as precipitation.
- The atmospheric component of the water cycle is the only one that "runs
up hill". The transfer of vapour by way of the atmosphere is the basic
supply of water for precipitation material.
- While there is as much water vapour entering the global atmosphere as there
is leaving it, such a balance does not exist at most individual locations
Water Vapour
- The amount of water vapour in air can range from near zero up to about
4% in a volume.
- Because water substance can exist in different phases within the temperature
and pressure ranges found in the atmosphere, there are upper limits to the concentration
of the water vapour phase in air. The maximum capacity of a volume of air to
hold water vapour depends solely on temperature, and increases as temperature
increases.
- The maximum water-vapour capacity of a volume approximately doubles for
each ten Celsius degree temperature increase. Similarly, a ten-degree drop in
temperature nearly halves the capacity of a volume to hold water vapour.
- One measure of the amount of water vapour actually in the air is called
the absolute humidity. Absolute humidity is the mass of water vapour in a unit
volume (this is water vapour density, commonly measured as grams of water vapour
per cubic metre). An alternative way to express absolute humidity is mixing
ratio, which is the ratio of the mass of water vapour to the mass of dry air
in the atmosphere, commonly expressed in grams (g) of water vapour per kilogram
(kg) of dry air. Typical mixing ratios range from 1.5-15.0 g kg-1
near the Earth's surface to 0.3-3.0 g kg-1 at 500 hPa (~5.5 km ASL).
- Relative humidity is expressed in per cent and is the ratio of the amount
of water vapour actually present in air to its maximum capacity at that temperature,
times 100.
- Dew point (or dew-point temperature) is the temperature to which air must
be cooled (at constant pressure) without changing the amount of water vapour,
so that the amount of water vapour actually in the air is equal to the maximum
amount that can be in the air at that same temperature.
Saturation and Precipitation
- A volume filled to its capacity by water vapour is said to be saturated.
When air is saturated, its relative humidity is 100%, and its dew point is the
same as its temperature.
- Liquid water and ice can change to vapour at any temperature they exist.
Such phase changes will occur when the region above the water or ice is not
saturated with water vapour.
- If saturated air is cooled, enough condensation will take place to maintain
saturation. This process results in clouds in the atmosphere or fog formation
near the ground.
- The formation of clouds can lead to precipitation. Precipitation is composed
of any or all of the forms of water particles, whether liquid or solid, that
fall from clouds and reach the ground. These forms include snow, rain, drizzle,
and hail.
Water Vapour Observation
- Water in the forms of both invisible vapour and visible cloud particles
is transported by winds and vertical motions throughout the global atmosphere.
- Although transparent to visible light, water vapour is detectable by weather
satellites because it is an efficient absorber and re-emitter of certain wavelengths
of infrared radiation.
- The special infrared sensors aboard weather satellites have revealed regions
of increased atmospheric water vapour concentration. These regions, sometimes
resembling gigantic swirls or plumes, can be seen to flow within broad-scale
weather patterns.
- Current research suggests that at any one time, atmospheric water vapour
may be found concentrated in several large flowing streams forming the equivalent
of "rivers in the sky".
Narrative
Water and Water Vapour
Liquid water covers over two-thirds (71%) of our planet's surface, while constituting
over half the mass of protoplasm, the substance of living matter. Ice covers
nearly 10% of the Earth's land surfaces in the form of ice sheets and glaciers.
Atmospheric water vapour is the parent of clouds and precipitation while playing
a major role of transporting energy on a global scale. Water in the Earth's
environment has the remarkable property of being the only substance that exists
naturally in significant quantities in all three states - solid (ice), liquid
(water),and gas (vapour) - at the temperatures and pressures found at and near
the Earth's surface.
Water vapour, invisible to the eye, is an extremely important atmospheric constituent.
It is primarily in the vapour phase that water substance is transported in air
from place to place on a global scale. Its condensation leads to clouds, which
in turn can produce precipitation. The atmosphere transports huge quantities
of water (vapour) and energy (latent heat), redistributing these so as to maintain
a balance of water and energy all over the globe. The water vapour also continually
absorbs infrared (heat) radiation, further complicating the Earth's energy balance.
Water Vapour in the Water Cycle
The hydrologic or water cycle is an overall picture of the
movement and exchange of water substance among the atmosphere, ocean and land.
Within the atmosphere, an unending flow of water substance is maintained as
energy from the sun evaporates enormous quantities of water from ocean and land
surfaces. Winds transport the moistened air to other regions where the water
vapour condenses to form clouds, some of which produce rain and snow. When precipitation
falls into the ocean, the water is ready to begin its cycle again. When it falls
on land, it may evaporate back to the atmosphere, or begin what can be a complex
journey back to the ocean.

Illustration of some of the complexities of the water cycle
Although the overall water cycle is very complex, the segment with which we
are most concerned has water substance travelling from the ocean to the atmosphere,
through the atmosphere, and back to the Earth's surface. This produces precipitation
and the fresh water necessary for life beyond the oceans. It is only the atmospheric
portion of the water cycle that can restore the water substance, in vapour form,
back to the level where it can begin the downward flow to completion in the
ocean.
At any given time, only 0.001% of Earth's water is in the atmosphere while 97%
is in the world's oceans. Additionally, approximately 2% is in ice fields and
glaciers, 0.6% is in ground water, and 0.01% is in rivers and lakes.
While 24% of all precipitation on a global scale falls over land, evaporation
from land surfaces amount to only about 15% of the total water vapour entering
the atmosphere. The imbalance is accounted for by the oceans which lose more
water by evaporation than they receive directly from storms. In other words
the oceans are the sources of the net gain of water by land surfaces. However,
this net gain of water is the amount eventually returned to the oceans by stream
runoff and ground water to maintain a net global balance of water.
The oceans cover more than 70% of Earth's surface to an average depth of about
4,000 metres. Each year, approximately a 1-metre layer of the ocean surface
is evaporated into the atmosphere. An equal amount is returned to the oceans
by the combination of precipitation and runoff. The total mass of water stored
in the atmosphere at any time is only enough to cover the globe with a layer
of liquid water 2.5 cm in depth. This is equivalent to only a little more than
a week's supply of the world's precipitation. Thus, the residence time of water
in the atmosphere is approximately ten days. For comparison, the residence time
of water in the oceans is 4,000 years (4,000 metres depth divided by annual
evaporation rate of 1 metre per year).
Annual amounts of precipitation measured at thousands of locations around the
world have been remarkably steady over the years. There have been no dramatic
short-term changes in the global sea level or in the amount of ice locked in
ice sheets and glaciers. Atmospheric measurements (globally averaged) also indicate
a quite constant water content. Since no water reservoir is changing significantly
(at least as far as we can measure with certainty), we can only conclude that
the global water cycle is essentially in balance.
While there is a world-wide balance in the amount of precipitation and evaporation,
a local balance does not exist at most locations on Earth. Imbalances are reflected
in the types of climates observed. Moist climates (such as tropical rain forests)
are found where precipitation exceeds evaporation, while dry climates (deserts)
prevail where evaporation exceeds precipitation.
Even the mid-latitude temperate climates have local imbalances. One need only
recall periods of several days of fine weather to be followed by a day or two
of rainy skies. Evaporation dominated the sunny times while precipitation far
exceeded evaporation during the storms. At the same time, the middle latitudes
are the recipients of moisture transported by the atmosphere from lower latitudes.
Evapotranspiration and Water Vapour
Water vapour reaches the atmosphere primarily through evapotranspiration from
a water source at the earth's surface. Evapotranspiration includes open-water
evaporation (from the ocean, a lake, river, or other surface water body), sublimation
of solid water (ice or snow surface) directly to vapour, or transpiration of
water from vegetation. Transpiration generally represents the highest source
of vapour from land surfaces, simply because water surfaces generally constitute
a smaller proportion of the total land area of continents; hence the use of
the term evapotranspiration to encompass all three forms of evaporation. A fourth,
relatively less important evaporation process occurs in the atmosphere itself,
that is, evaporation of falling precipitation, referred to as virga by weather
observers.
Water vapour is found in air in varying amounts ranging from near zero up to
about 4% by volume, depending upon both temperature and availability of water.
The highest water vapour content is found above hot, wet surfaces. The lowest
is where temperatures are lowest or in desert areas where the surface water
source is extremely low . It is important to remember that the total mass of
water in the atmosphere at any time is only enough, if it all precipitated,
to cover the globe with a layer of water 2.5 cm deep.
At any given temperature, there is a maximum amount of water vapour that can
exist in a volume of air. This occurs because of the possible co-existence of
vapour, liquid and solid phases within the temperature and pressure ranges found
in the atmosphere. Once the maximum water vapour concentration is reached for
a particular temperature, any additional vapour will change phase to liquid
or solid (rain or snow).
The higher the temperature, the more water vapour a volume of air is capable
of holding. Thus, any change in temperature alters the volume's water-vapour
capacity. As air warms, the capacity for holding water vapour increases, and
as it cools, the capacity decreases.
The maximum water vapour capacity of a volume of air increases at an increasing
rate as temperature increases. For the range of temperatures normally found
near the Earth's surface, this capacity approximately doubles for each 10ºC
of warming. Conversely, a 10ºC cooling nearly halves the capacity of a
volume to hold water vapour.
Temperature (oC)
|
Vapour Capacity (g/m3)
|
-20
|
1.1
|
-15
|
1.6
|
-10
|
2.3
|
-5
|
3.4
|
0
|
4.8
|
5
|
6.8
|
10
|
9.4
|
15
|
12.9
|
20
|
17.3
|
25
|
23.2
|
30
|
30.5
|
How water vapour capacity varies with temperature near sea level (Saturation
Absolute Humidity)
Water vapour behaves as other gaseous components of air as long as its maximum
concentration has not been reached.
When water vapour is added to a volume of air with no change in temperature
or pressure, the density of the volume decreases. Whenever a mixture of gases
(such as air) is kept at the same temperature and pressure, the total number
of molecules will remain constant in a given volume. Adding lighter water molecules
will force heavier air molecules from the volume, resulting in a lighter volume.

Humid air is less dense than air without water vapour
Humidity is the measurement of the water vapour content of air. The term humidity
is a general term referring to any one of a number of ways of specifying atmospheric
water vapour content. Humidity may be given as absolute or relative, or even
as a temperature reflecting moisture content, such as dew point. It can be measured
with a variety of instruments, including psychrometers, hygrometers, and dew
cells.
One measure of the amount of water vapour actually in the air is called absolute
humidity. Absolute humidity is the mass of water vapour in a unit volume, or
water vapour density, usually measured in grams of water vapour per cubic metre.
A commonly used measure of atmospheric water vapour content is relative humidity.
Relative humidity, expressed in per cent, is the amount of water vapour actually
present in air as compared to its maximum capacity at that temperature. Relative
humidity is temperature dependent, since the maximum possible amount of water
vapour contained in a volume of air is related to temperature. Consequently,
relative humidity values on a typical day decrease during the day as temperatures
rise, and increase at night as temperatures lower. However, the absolute humidity
does not change unless vapour is either added or taken away.
The dew point, or dew-point temperature, is another common humidity measure.
It is the temperature to which the air has to be cooled at constant pressure
(without changing the water vapour content) so that the actual amount of water
vapour in the air is equal to the maximum amount that could be in the air at
that temperature. High dew points indicate high atmospheric water vapour content.
Low dew points indicate low content. The addition of water vapour to the air
increases the dew point, while removing water vapour lowers it.
Water vapour is extremely important to weather. It condenses to form cloud particles
which can lead to precipitation. It releases large amounts of latent heat when
changing from vapour to liquid or ice, serving as a major energy source for
storms ranging in size from local thunderstorms to hurricanes to large extra-tropical
weather systems. In addition, water vapour strongly absorbs and re-radiates
Earth's long-wave infrared (heat) radiation, making it the major "Greenhouse"
gas in the planet's heat and energy balance.
Note: For a simple exercise demonstrating the relationship between temperature,
water vapour content, and dew point, see [Activity: Water
Vapour Investigation].
Saturation, Condensation and Precipitation
A volume of air filled to its capacity for water vapour is said to be saturated.
Saturation can be achieved in different ways. As a volume of air cools, its
capacity to hold water vapour decreases. As the air is cooled, it reaches saturation
when its capacity is reduced to equal the amount of water vapour it contains.
Saturation can also occur if water vapour is added to a volume of air until
it is filled to its capacity. When air is saturated, its relative humidity is
100%, and, by definition, its dew point and its temperature must be the same.
Vaporization can occur whenever the region above a water or ice surface is not
saturated with water vapour. Evaporation increases the water vapour content
in the region (unless the vapour is removed by some means). The addition of
vapour can lead to saturation. If the region above the water or ice is enclosed,
it will eventually become saturated.
Condensation is the general term for the change of phase from a vapour to a
liquid or directly to ice. It will occur if a saturated region is cooled and
there is a surface on which condensation can begin. Only enough condensation
will take place to maintain saturated conditions. Condensation is taking place
whenever clouds and fogs are seen forming. [Note: the change of phase
directly from vapour to ice or from ice to vapour curiously are both called
sublimation by meteorologists.]
Rising air cools by expansion. As a volume of air cools, its capacity to hold
moisture decreases and it will eventually reach saturation. If cooling continues,
water vapour will condense on tiny particles in the air to form minute liquid
water droplets or solid ice crystals. This is the most common way that clouds
are produced. Cloud bases are located at the elevation at which saturation is
first achieved. Further cooling and condensation causes these small water droplets
or ice crystals within clouds to multiply, eventually collecting together to
form larger precipitation particles, which reach the earth's surface as either
snow, rain, drizzle, or hail.
There are other ways that air can be cooled to saturation. One is by moving
warm, humid air over a cooler surface. The air is then cooled by contact (conduction)
and resulting saturation produces advection fog, a common occurrence over Canada's
coastal waters. Another common method of cooling humid air is by radiative heat
loss from the land surface overnight under clear skies, which in turn cools
the air by direct contact to saturation, resulting in radiation fog.
Saturation can also occur if water vapour is added to already moist air. Enough
condensation can then take place to maintain saturation levels of water vapour.
This can be seen at times when cold air moves over a warmer, wet surface, causing
evaporation which often produces saturation that is called steam fog. This frequently
occurs over Canada's coastal and inland water bodies in the fall when cool air
flows over a still relatively warm water surface. Rain evaporating into already
humid air to produce pre-frontal fog is yet another means of achieving saturation-condensation.
Water Vapour Observation
Due to unequal heating of the atmosphere and other factors, motions ranging
from the microscopic to broad-scale planetary circulation patterns form. The
water which evaporates from the surface of the ocean releases energy which helps
to maintain the general circulation of the atmosphere. It is through this circulation
that water, as vapour and cloud, is transported by wind and vertical motions
throughout the global atmosphere.
The movement of water in all its phases through the atmosphere can be monitored
on a global scale by the use of instruments aboard weather satellites. The motion
of the solid and liquid water found in clouds can be observed in the visible
and infrared cloud imagery used on daily TV weather reports. This is not true
for the invisible water vapour phase.
Although transparent to visible light, water vapour is a very good absorber
and re-emitter of infrared radiation at certain wavelengths. This property enables
the atmospheric water vapour to be detected from above by the special infrared
sensors carried aboard weather satellites.
The two satellite images (Figure 1 and 2)
demonstrate distinctly different perspectives of the atmosphere. The visible
image (Figure 1) views the Earth and the atmosphere
as they would be seen by the human eye. Clouds are reflective surfaces, hence
appear as grey or bright white features in the image. The water vapour image
(Figure 2) depicts clouds (condensed water) and water
vapour (a gas invisible to the eye) for the middle and upper portions of the
troposphere (especially 500 - 200 hPa).
High cloud types are bright white on the water vapour image and also quite apparent
on the visible image. Low clouds may be seen in the visible image, but are not
detectable in the water vapour image. The most interesting difference, however,
is that regions of greater water vapour content (not condensed as cloud) appear
milky white in the water vapour image, but do not appear on the visible image
(since water vapour is an invisible gas).

Figure 1 - Visible satellite image
The features of the water vapour image and how these features move and change
with time are just now being related to atmospheric circulation systems and
processes. Water vapour imagery is becoming a valuable tool used to confirm,
modify or significantly change weather forecasts.
Recent improvements in satellite imagery from space have revealed regions of
concentrated atmospheric water vapour in the middle levels of the atmosphere.
These streaks of water vapour in the imagery are called plumes due to their
resemblance to smoke plumes. The plumes, often originating in the tropics, have
been observed in motion distributing water vapour across the globe. Their influence
on weather patterns may range from local storms up to global in scale.
Satellite imagery is revealing that, at any one time, up to half a dozen streams
of vapour exist in each hemisphere. These plumes are each several hundred kilometres
wide and several thousand kilometres long. The total vapour amounts in one of
these plumes would be equivalent to the water content of a major river on land.
These "rivers in the sky" seem to be associated with the moisture
supply for hurricanes, for major summer thunderstorm concentrations and for
mid-latitude winter storms. Apparently, it is in this way that water vapour
reaches higher latitudes to fuel much of the precipitation in the water cycle.

Figure 2 - Water vapour satellite image
Activity
Activity - Water Vapour Investigation
After, completing this investigation, you should be able to:
- Explain with cups of different sizes how the "capacity" of air
to hold water vapour varies with temperature.
- Use the cups and styrofoam packing "peanuts" as a model to explain
relationships between the "capacity" of air to hold water vapour
and the actual amount of water vapour in the air.
Materials
Four 375 ml (12-ounce) clear or translucent drinking cups for every two learners,
enough styrofoam "peanut" packing material (or popped popcorn) to
fill one cup, scissors, permanent marking pen.
Steps to prepare the set of cups for use in this activity:
- Fill a 375 ml (12-ounce) cup to the brim with water. Pour from that cup
into another until the water levels in both are the same. Trace the water line
on the outside of both cups with a permanent marking pen.
- Empty the water from one of these and cut along the traced line to make a
187.5 ml (6-ounce) cup. Now pour the water remaining in the 375 ml (12-ounce)
cup into a third cup until their water levels are the same. Trace their water
levels.
- Empty the water from the third cup and cut it down to the marked water level
to make a cup that holds 93.75 ml (3-ounces).
- You should end up with three cups - one 93.75 ml (3-ounce) cup, one 187.5
ml (6-ounce) cup that has a line marking the 93.75 ml (3-ounce) level, and one
375 ml (12-ounce) cup with lines marking 187.5 and 93.75- ml (6- and 3-ounce)
levels.
- Write a large 0 on the side of the smallest cup, 10 on the middle size, and
20 on the largest cup to indicate 0, 10, and 20 degrees Celsius. Use these cups
as guides to preparing other sets.
- The fourth and unmarked cup will hold the styrofoam packing "peanuts"
(or popped corn).
Method
Cups of different sizes are used in this exercise to represent the "capacity"
of air to hold water vapour at 0, 10, and 20 degrees Celsius. Styrofoam packing
"peanuts" (or popped popcorn) are poured into the cups to represent
the water vapour actually in the air.
Start the activity by filling the large unmarked cup approximately level with
packing peanuts. Tap the cup gently to help the material settle as you fill
the cup. This is the supply of packing peanuts you will use in this exercise.
This activity involves the use of four cups. The unmarked cup is used to store
the packing peanuts. The largest marked cup is twice the capacity of the mid-size
cup. The mid-size cup is twice as big as the small cup. The marked cups represent
the capacity of air to hold water vapour at 0, 10, and 20 degrees Celsius. Each
cup is labelled by the temperature related to its capacity.
- Fill the small 0-degree cup with packing peanuts until the contents are
level with the top of the container. Pour the contents into the mid-size 10-degree
cup. Repeat this procedure until the 10-degree cup is level full. Now pour the
filled 10-degree cup into the 20-degree cup until it is full. Assuming the cups
represent the capacities of air to hold water vapour at 0, 10, and 20 degrees,
complete the following statement:
The capacity of the air to hold water vapour approximately ( )
when the temperature increases 10 Celsius degrees.
- Starting with a filled 20-degree cup, pour its contents into the 10-degree
cup until it is level full. Now pour the contents of the 10-degree cup into
the 0-degree cup until filled to the brim. Now complete the following statement:
The capacity of the air to hold water vapour approximately (
) when the temperature lowers 10 Celsius degrees.
- Now empty the 20-degree cup and pour the filled 0-degree cups into the large
cup until it is full. Based on this, complete the following statement:
The capacity of the air to hold water vapour increases approximately (
) times when the temperature rises 20 Celsius degrees.
- According to the same observations, what happens to the capacity of air
to hold water vapour as the temperature falls 20 Celsius degrees?
- When air cools its capacity to hold water vapour decreases, and any excess
water vapour must condense. This can be demonstrated by attempting to pour all
the packing peanuts from a filled 20-degree cup into the 10-degree cup. Level
the top on the 10-degree cup. The overflow represents the water vapour that
condensed out. In this example of the 10-degree cooling, how much of the water
vapour condensed to 1iquid as the temperature dropped 10 degrees?
- Air filled to its capacity with water vapour is called saturated air. If
saturated air at 20 degrees is cooled 20 degrees, how much of its water vapour
must condense?
- Saturated air has a relative humidity of 100%. Relative humidity is a measure
of the amount of water vapour actually in the air compared to the amount it
would hold if saturated at the same temperature. Pour a full 0-degree cup into
a 10-degree cup to determine what the relative humidity would be if air saturated
at 0 degrees is warmed 10 degrees with no addition of water vapour. What is
it? What would the relative humidity be if that same air were warmed another
10 degrees to 20 degrees Celsius?
- Explain in your own words why in cold weather the relative humidity in heated
buildings (without humidifiers) are quite low.
- Dew point is another common humidity measure. It is the temperature to which
air has to be cooled (without changing the amount of water vapour in the air)
to become saturated. Whenever air is saturated, its temperature and dew point
will be the same. What is the approximate dew point of air at 20 degrees with
a relative humidity of 50%? To find out, fill the 20-degree cup half full. Then,
pour it into the 10-degree cup.
- What is the dew point of air saturated at 0 degrees when the air temperature
is raised to 10 degrees without the addition of water vapour? To find out, pour
a filled 0-degree cup into 10-degree cup and ask yourself whether or not the
dew point changed.
- If saturated air at 20 degrees is cooled to 10 degrees, what is its final
dew point? To help find your answer, attempt to pour a filled 20-degree cup
into l0-degree cup while asking yourself how much water vapour the l0-degree
cup is holding compared to its capacity.
- In general, when saturated air is cooled, what happens to its capacity to
hold water vapour, its dew point, and its relative humidity? Refer to your observations
made above.
- Describe, in your own words, the water vapour and temperature relationships
which must exist for cloud, dew, and frost formation.
- Look up and write out specific definitions for the following terms:
- Relative Humidity
- Dew Point
Activity - The Atmospheric Pipeline
Upon completing this activity, you should be able to:
- calculate the approximate volume of storm precipitation.
- estimate the surface water evaporated to supply the storm.
- evaluate the amount of fresh water runoff from the storm.
- explain how topographic features affect precipitation amounts.
Introduction
Atmospheric storm systems can be a nuisance for picnics, a welcome relief to
a drought, or disastrous flooding - bringing everything from joy to inconvenience
to untold hardship and destruction. These storms are an integral part of the
Earth's weather and climate system and the water cycle.
A strong spring storm on March 11-13, 1993 brought widespread rain and heavy
snow to the Gulf of Mexico and the Eastern United States. Several US states
were plagued by crippled transportation due to deep, wet snows and widespread
flash flooding, both from heavy rains and subsequent snowmelt. In all, over
200 people died from this one storm.
The following activity looks at this particular storm to examine the atmosphere's
ability to transport water substance. (Note: the precipitation data is from
US National Weather Service (NWS) and will be presented in its original format,
i.e. inches, miles, etc).
Liquid water is evaporated from the surface. Atmospheric circulation patterns
transport this water vapour to other locations where storm systems convert the
vapour back to its liquid and solid phases forming clouds and precipitation.
The precipitation is returned to the surface, renewing our fresh water resources
and completing the cycle. This activity will allow you to calculate the approximate
amount of water that fails from a major storm system. The accompanying map shows
selected total precipitation amounts (in inches) from the storm. Snowfall amounts
have been converted to comparable rainfall amounts. In most areas, the ground
was already saturated or still frozen, so that precipitation and melt-water
became "runoff".
Procedure
- From the displayed total precipitation amounts on the map
- Spring Storm March 11-13, 1993 Total Precipitation, estimate to
the nearest half inch (0.5, 1.0, 1.5, etc.), the average amount of precipitation
for the entire area of each state. Ignore the states where no precipitation
is given. Fill the column in the table below with the
average values from each state.
- Multiply the numbers across each row of the table to obtain products. The
approximate state areas, in square miles, are given. The area times precipitation
depth will be the water volume given in units of square miles-inches. Then sum
the products for the states listed in the table to obtain a grand total volume.
- The Gulf of Mexico with a surface area of approximately 600,000 square miles
serves as a vapour source region for many eastern U.S. storms. If one assumes
that all the water for this storm was originally evaporated from the Gulf of
Mexico, the depth of water needed may be found by dividing the grand total volume
above by 600,000 (6 x 105). This is the depth equivalent of water
evaporated from the entire Gulf area in inches.
Equivalent depth of evaporated water ( )
inches.
- To determine the weight of water precipitated from this storm, first multiply
the grand total volume above by 2,323,200 (2.3232 x 106) to convert
the total into cubic feet. [The multiplying number is the number of square feet
in a square mile divided by 12 inches per foot.] Then multiply this total by
62.4 pounds per cubic foot (density of fresh water) to obtain the total weight
of water precipitated by the storm.
Total weight of storm water (
) pounds.
- To determine the volume of fresh water runoff from this storm, divide the
total cubic feet of water found above by 1.47 x 10¹¹, the number of
cubic feet in a cubic mile. This number of cubic miles of water may then be
compared to the 116 cubic mile volume of fresh water in Lake Erie by taking
the number of cubic miles of storm water and dividing by 116. This is the equivalent
fraction of Lake Erie that would be filled, by the water running off from this
one major storm.
Volume of fresh water runoff (
) cubic miles.
Equivalent fraction of lake Erie volume ( ).
State
|
Area in square miles (mi2)
|
Avg precip. (in.)
|
Product
|
Alabama |
51,000
|
|
|
Connecticut |
5,000
|
|
|
Delaware |
2,000
|
|
|
Florida |
54,000
|
|
|
Georgia |
58,000
|
|
|
Kentucky |
40,000
|
|
|
Louisiana |
45,000
|
|
|
Maine |
31,000
|
|
|
Maryland |
10,000
|
|
|
Massachusetts |
8,000
|
|
|
Mississippi |
47,000
|
|
|
New Hampshire |
9,000
|
|
|
New Jersey |
7,000
|
|
|
New York |
47,000
|
|
|
North Carolina |
49,000
|
|
|
Ohio |
41,000
|
|
|
Pennsylvania |
45,000
|
|
|
Rhode Island |
1,000
|
|
|
Tennessee |
41,000
|
|
|
Texas |
262,000
|
|
|
Vermont |
9,000
|
|
|
Virginia |
40,000
|
|
|
West Virginia |
24,000
|
|
|
Grand total:
|
|
Questions
1. What is the greatest amount of precipitation (at a single station) shown
on the map (Spring Storm March 11-13, 1993 Total Precipitation)
? ( ).
In what state did it occur? ( ).
Is the heaviest precipitation concentrated in a single area or does it occur
in several disconnected areas? (
).
2. Using a topographic or relief map, can you find a general relationship between
elevation and the larger precipitation amounts? ( ).
What does this relation appear to be?
_____________________________________________________________
_____________________________________________________________
3. (a) How does your calculated average depth of water evaporated from the
Gulf of Mexico compare to the average depths of precipitation you estimated
for the states?
_____________________________________________________________
How do the areas of the Gulf of Mexico and the Eastern United States compare,
roughly? (
). What does this imply about the transport of water from ocean to land locations
by storms?
______________________________________________________________
______________________________________________________________
(b) Is it reasonable that this transport occurs from warm tropical ocean areas
to higher latitude cooler land areas? ( ).
Why or why not?
______________________________________________________________
______________________________________________________________
4. Atmospheric storms differ in intensity, frequency and location around the
world, but assume this storm is somewhat typical in moving water substance,
and was the sole disturbance occurring during this one week. How much total
depth of water would be evaporated/precipitated in a year?
______________________________________________________________
How does this total compare to the world-wide average given elsewhere in this
Teacher's Guide?
_______________________________________________________________
_______________________________________________________________

Additional Activities
- Obtain a metal container such as a soft drink can (with top removed) and
a liquid crystal strip thermometer or other thermometer that makes good contact
with the can side. Attach the thermometer to the side of the can. Fill the can
approximately two-thirds full with water. Begin to add crushed ice to the water
and stir. Continue adding ice to cool the water and the container. Carefully
observe the outside of the can for the formation of dew - condensation on the
sides and note the temperature when it just begins to form. This is the dew
point temperature and is the temperature at which the actual amount of moisture
in the surrounding air is the maximum possible for that temperature.
- Create your own hydrologic cycle by placing soil in one end of an aquarium.
Add some water in the other end to form "land" and "sea"
regions. Cover the aquarium with a metal baking sheet over the land end and
a plastic sheet over the sea end, sealing the top. Shine a lamp into the aquarium
side to simulate the sun. Finally place some ice on the metal baking sheet.
Water will be evaporating from the land and water surfaces with vapour condensing
on the cool metal sheet and "precipitating" back down.
- Use a clear cooking pan or beaker. Fill with crushed ice and water. Allow
to stand until the water and ice mixture comes to the equilibrium freezing temperature
of 0 degrees C, adding more ice if necessary to obtain a mixture with sufficient
ice. Place the pan or beaker on a hot plate or heat source and heat slowly.
Stir and continue to measure the temperature of the mixture until all the ice
has melted. Does the temperature remain at (or near) the freezing temperature
(0°C) during this time? Where does the heat that is being added go if the
temperature does not increase? [This is latent heat that goes to change the
phase of water from solid to liquid.]
- Cut three one-metre square pieces of clear plastic sheeting material. Place
one over a grassy surface, one over bare soil and one on an asphalt or concrete
surface. After half an hour, observe the sheets of plastic to see which surface
has had the most evaporation. [Evaporation from soil and transpiration from
vegetation surfaces combined is called evapotranspiration.] Try this experiment
at various times of the day or under various cloud cover conditions to investigate
the change of solar radiation. Also try this experiment with differing humidity
and wind conditions.
Created :
2002-06-06
Modified :
2004-01-06
Reviewed :
2003-07-09
Url of this page : http://www.msc.ec.gc.ca /education/teachers_guides/module12_water_vapour_and_the_water_cycle_e.html
The Green LaneTM, Environment Canada's World Wide Web Site.
|